TITLE

Mould Running System Design to Achieve the Minimum Waste

AUTHOR(S)
Monkova, Katarina; Monka, Peter; Cizikova, Andrea; Hric, Slavomir
PUB. DATE
May 2014
SOURCE
Advanced Materials Research;2014, Issue 933, p963
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The article deals with the mould running system design. The goal of design presented in the article was to propose the mould form so to be achieved the minimum waste for selected component. Studied component is intended to serve as a stopper in the automotive spotlight. The waste is considered the material that solidifies in the volume of plastic inside the running system. 3D model of the mould was created in Autodesk Inventor Proffesional software and then solidification of material was simulated in Autodesk Moldflow Insight software. There were designed three alternatives of running system at which the waste amount was evaluated. On the basis of the best solution, the real form was manufactured and placed into the injection moulding machine Arburg Allrounder 320 C.
ACCESSION #
96280744

 

Related Articles

  • Influence of Melt Mixer on Injection Molding of Thermoset Elastomers. Rochman, Arif; Zahra, Keith // AIP Conference Proceedings;2016, Vol. 1769 Issue 1, p1 

    One of the drawbacks in injection molding is that the plasticizing screw is short such that polymers having high concentrations of additives, such as thermoset elastomers, might not mix homogeneously within the short period of time during the plasticizing stage. In this study, various melt...

  • Analysis of the process influences on injection molded thermosets filled with hollow glass bubbles. Hopmann, Christian; Theunissen, Matthias; Haase, Stefan // Journal of Polymer Engineering;Aug2018, Vol. 38 Issue 7, p695 

    Thermoset molding compounds have a wide range of beneficial properties such as easy handling, high temperature, chemical resistance, low shrinkage as well as low electrical conductivity. However, these properties come at the cost of a higher density than technical thermoplastic materials and...

  • EFFECT OF CARBON FIBER, SILICA AND FLY-ASH PARTICULATE ADDITION on TENSILE and IMPACT BEHAVIOUR of POLYESTER AND EPOXY RESIN. Kumar, P. Nantha; Rajadurai, A. // Applied Mechanics & Materials;2014, Issue 592-594, p186 

    Thermosetting and thermoplastic resins are becoming widely accepted alternate materials in engineering industry. Industries seek alternate materials stalling from containers to aircraft parts for reducing weight and increasing durability. Mere resin based plastic components may not fulfil these...

  • TPE Is Super-Soft and Water-Clear.  // Plastics Technology;Dec2002, Vol. 48 Issue 12, p26 

    Focuses on the softest injection moldable thermoplastic elastomer (TPE) alloy made by GLS Corp. in McHenry, Illinois. Features of TPE; Range of application of TPE.

  • Hard rules for soft-touch overmolding. Caamano, John; Hoffman, Jean M. // Machine Design;5/9/2002, Vol. 74 Issue 9, p60 

    Presents information on the use of a two-step injection molding process to mold soft-touch grips and watertight seals onto structural plastics. Details of the process; Advantages of parts containing hard-soft combinations; Types of thermoplastic-elastomers that can be made with two-shot...

  • Gas Assist Work for Thermosets And Smaller Parts, Too. Knights, Mikell // Plastics Technology;May2003, Vol. 49 Issue 5, p65 

    Focuses on gas-assist injection molding process for thermosets in the U.S. plastics industry. Use of gas assist for molding of smaller plastic parts; Gas-assist process use by the company Bulk Molding Compounds Inc.; Plastic parts and equipment where the gas-assist technology can be used.

  • Inside the Barrel. Anderton, Jim // Canadian Plastics;Jul/Aug2005, Vol. 63 Issue 7, p36 

    Focuses on the processes inside the barrel of an injection molding machine. Reason behind the ongoing research on inner workings of molding; Information on melting thermoplastics; Significance of pitch and profile of a screw in controlling the barrel process.

  • Maximum efficiency for complex composite processes.  // Tehnicki vjesnik / Technical Gazette;2017 Supplement1, Vol. 24, pX 

    No abstract available.

  • Overmoulding of Plane Structural Foamed Parts With a Second Thermoplastic Component. Mueller, Johannes; Spoerrer, Andreas; Altstaedt, Volker // Cellular Polymers;2012, Vol. 31 Issue 4, p223 

    Over the last few years some highly-efficient manufacturing processes in the field of foam injection moulding occurred based on new developments in the machine, the mould and the material technology. The manufacturing of car interior parts with a soft touch surface for example became possible in...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics