TITLE

A critical thickness condition for a strained compliant substrate/epitaxial film system

AUTHOR(S)
Freund, L. B.; Nix, W. D.
PUB. DATE
July 1996
SOURCE
Applied Physics Letters;7/8/1996, Vol. 69 Issue 2, p173
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The physical system under study is a single crystal film grown epitaxially on a substrate of comparable thickness which is constrained to remain flat. In general, the layers are strained due to a mismatch in lattice parameter between the film and substrate materials. The free energy change of the system due to formation of strain-relaxing interface misfit dislocations is estimated, and the discriminating case of zero energy change leads to a critical thickness condition on mismatch strain, film thickness, substrate thickness, and crystallographic slip orientation which is necessary for the spontaneous formation of such dislocations. The condition obtained generalizes the Matthews–Blakeslee (MB) criterion for a thin film on a thick substrate to the case of a complaint substrate/epitaxial film system, and it reduces to the MB criterion when either the film or substrate is relatively thick. © 1996 American Institute of Physics.
ACCESSION #
6289464

 

Related Articles

  • A novel method for determining the anchoring energy function at a nematic liquid crystal-wall interface from director distortions at high fields. Yokoyama, H.; van Sprang, H. A. // Journal of Applied Physics;5/15/1985, Vol. 57 Issue 10, p4520 

    Presents a method for determining the anchoring energy function at a nematic liquid crystal-wall interface from director distortions at high fields. Theory of the determination of the anchoring energy function; Discussion of findings.

  • Use of the microindentation technique for determining interfacial fracture energy. Rosenfeld, L. G.; Ritter, J. E.; Lardner, T. J.; Lin, M. R. // Journal of Applied Physics;4/1/1990, Vol. 67 Issue 7, p3291 

    Presents a study which determined the interfacial fracture energy of epoxy coatings on soda-lime glass substrates using microindentation technique. Model for calculating fracture energy; Amounts of opening and shear loadings at the debond crack tip; Comparison with values determined by the...

  • Determination of potential distribution in a three-barrier structure. Yodgorova, D. M.; Zoirova, L. X.; Karimov, A. V. // Semiconductor Physics, Quantum Electronics & Optoelectronics;2006, Vol. 9 Issue 3, p35 

    Model m1-p-n-m2 structures with three barriers were considered; construction and technology of manufacturing the three-barrier m1-pAlGaInAs-nGaAs-m2 structure are presented. Experimental methods to determine voltages across every junction of the three-barrier structure were proposed. The...

  • Competition between deflection and penetration at an interface in the vicinity of a main crack. Martin, E.; Poitou, B.; Leguillon, D.; Gatt, J. M. // International Journal of Fracture;Jun2008, Vol. 151 Issue 2, p247 

    The mechanisms which govern crack deflection and crack penetration at interfaces must be understood in order to design composites and layered materials. Experimental observations have shown that a realistic description of crack deflection must take into account the initiation of fracture...

  • Edge-to-Edge Matching--The Fundamentals. Kelly, P. M.; Zhang, M.-X. // Metallurgical & Materials Transactions. Part A;Mid-March2006, Vol. 37 Issue 3A, p833 

    The basis of the present authors' edge-to-edge matching model for understanding the crystallography of partially coherent precipitates is the minimization of the energy of the interface between the two phases. For relatively simple crystal structures, this energy minimization occurs when...

  • Theory of activated rate processes in the weak and intermediate friction cases: New analytical results for one and many degrees of freedom. Shushin, A. I. // Journal of Chemical Physics;5/15/1994, Vol. 100 Issue 10, p7331 

    Simple analytical expressions for the reaction rate of activated rate processes are derived in the weak/intermediate friction limit for one and many degrees of freedom and for finite microcanonical reaction rates. The expressions are obtained by analytical solution of the steady-state integral...

  • Droplet introduction into a pen-shaped portable reaction system by gravity and interfacial forces. Shikida, M.; Inagaki, N.; Okochi, M.; Honda, H.; Sato, K. // Micro & Nano Letters;Apr2011, Vol. 6 Issue 4, p253 

    A pen-shaped platform that is similar to a mechanical pencil was proposed for producing the portable biochemical reaction system presented in previous work. The key component, the sample introduction unit, in the system was proposed in this work. The unit was fabricated by using a heat...

  • THE MULTISCALE MODEL COMBINING ELASTIC THEORY WITH AB INITIO CALCULATIONS FOR METAL–CERAMIC INTERFACES. ZHANG, YING; YAO, YUGUI // Modern Physics Letters B;12/30/2008, Vol. 22 Issue 32, p3135 

    The generalized two-dimensional Peierls–Nabarro (PN) model7 for studying interfaces is developed further, where an exact generalized stacking fault energy γ-surface obtained from ab initio calculations acts as an input function for the generalized PN model. Using the multiscale...

  • Influence of oscillating features of a laser-induced bubble on laser propulsion in water environment near different interfaces. J. Chen; B. Han; L. Dou; Y.-X. Pan; Z.-H. Shen; J. Lu; X.-W. Ni // European Physical Journal - Applied Physics;Nov2010, Vol. 52 Issue 12, p0 

    Laser propulsion in a water environment is influenced by oscillating features of a laser-induced bubble. In our study an optical beam deflection method is used to investigate dynamics of laser-induced semispherical cavitation bubbles near three different interfaces: the rigid boundary...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics