TITLE

Effect of mandrel-cores on springback and sectional deformation of rectangular H96 tube NC bending

AUTHOR(S)
Zhu, Y.; Liu, Y.; Yang, H.
PUB. DATE
April 2015
SOURCE
International Journal of Advanced Manufacturing Technology;Apr2015, Vol. 78 Issue 1-4, p351
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
To reveal the effect mechanism of mandrel-cores on springback and sectional deformation of rectangular H96 tube NC bending, the stress variation caused by using different numbers of cores are analyzed based on the finite element simulation as well as its relationship with the springback and sectional deformation. Results show that the flexible core causes larger tangential stress in the bending stage, which leads to larger springback. The frequency of repeated loading-unloading process of the tube increases with the increase of the core number, and the reloading process always keeps in plastic deformation range, so the varied elastic modulus effect and the Bauschinger effect are highly suggested to be considered to predict springback accurately. The retracting mandrel is an elastic process that will average and reduce the magnitude of stress, and the stress reduction nearly increases with the increase of the core number. The variation trend of sectional deformation is determined by both the tangential stress and the circumferential stress. In addition, the performances of the mandrel-core die and the PVC mandrel on the H-bending process are compared. It is found the mandrel-core die has advantage to prevent the width and height deformations of H-bend when compared with the PVC mandrel, and this phenomenon is absolutely opposite with that in E-bending process.
ACCESSION #
101679562

 

Related Articles

  • The Multi-Breakage Phenomenon in Air Bending Process. Vorkov, Vitalii; Aerens, Richard; Vandepitte, Dirk; Duflou, Joost R. // Key Engineering Materials;2014, Vol. 611-612, p1047 

    In this work, the multi-breakage effect has been studied by means of an experimental campaign and finite element analysis. We suggest that large radius bending (XL-bending) consists of three phases that are distinguishable according to the type of contact of the plate with the tool: 1-point,...

  • An Investigation into the Different Hardening Models in Reverse Forming of Thin Sheets. Kadkhodayan, M.; Mosayebi, J. // Advances in Mechanical Engineering (Hindawi Publishing Corporati;2009, Vol. 1, p1 

    This paper discusses a finite element analysis of the Bauschinger effect in the reverse cup drawing process, taken from the NUMISHEET'99 (Gelin and Picart, 1999) benchmark. In order to study the Bauschinger effect, several hardening models are considered such as isotropic, kinematic, and...

  • Analytical prediction of springback based on residual differential strain during sheet metal bending. Yi, H. K.; Kim, D. W.; Van Tyne, C. J.; Moon, Y. H. // Proceedings of the Institution of Mechanical Engineers -- Part C;Feb2008, Vol. 222 Issue 2, p117 

    As the springback of sheet metal during unloading may cause deviation from a desired shape, accurately predicting springback is essential for the design of sheet stamping operations. Finite-element models have not been successful in predicting springback; hence there is a need for analytical...

  • Stress strain state of mechanically heterogeneous welded joint with mild square butt weld subjected to elastic pure bend. Vaičiulis, D.; Bražėnas, A. // Mechanika;2007, Vol. 63 Issue 1, p5 

    In this paper are presented the dependencies for the determination of stress and strain state in mechanically heterogeneous welded joints with square butt simplified mild weld (weld without reinforcements) at plane deformation under elastic static loading subjected to pure bending. This method...

  • Deformation Characteristics of Advanced High Strength Steel Under Cyclic Bending and Reversed Bending. Fuh-Kuo Chen; Sin-Liang Lin; Heng-Kuang Tsai; Yi-Wei Lin; I-Kai Lin // Key Engineering Materials;2015, Vol. 651-653, p175 

    In the present study, the Bauschinger effect exhibited in the advanced high strength steel under cyclic bending and reversed bending deformation was examined by both the experimental approach and the finite element analysis. The cyclic tension-compression tests were first conducted for the DP590...

  • Influence of Bauschinger effect on springback and residual stresses in plane strain pure bending. Alexandrov, Sergei; Hwang, Yeong-Maw // Acta Mechanica;Aug2011, Vol. 220 Issue 1-4, p47 

    finite deformation elastic plastic analysis of plane strain pure bending of a wide sheet is presented. The general closed-form solution is proposed for a kinematic hardening law assuming that the material is incompressible. The stage of unloading is included in the analysis to investigate the...

  • LENGTH AND WIDTH EFFECTS OF METAL FILMS ON STRESS-INDUCED BENDING OF SURFACE MICROMACHINED CANTILEVER CURVED GRATING. KUO, JU-NAN // Surface Review & Letters;Feb2012, Vol. 19 Issue 1, p1250001-1 

    In this study, the length and width effects of metal films on the stress-induced bending of a surface micromachined cantilever curved grating are systematically investigated. A characterization of cantilever curved gratings with various lengths and widths was conducted to observe out-of-plane...

  • Nonlinear spatial bending of shear-deformable curvilinear rods. Levyakov, S. // Journal of Applied Mechanics & Technical Physics;Mar2012, Vol. 53 Issue 2, p258 

    A finite element is proposed for analyzing nonlinear deformation and stability of three-dimensional rods at arbitrarily large elastic displacements. Timoshenko's model is used for taking transverse shear strains into account. The accuracy and convergence of numerical solutions are studied by an...

  • A Novel Specimen for Investigating the Mechanical Behavior of Elastomers Under Multiaxial Loading Conditions. Mars, W.V.; Fatemi, A. // Experimental Mechanics;Apr2004, Vol. 44 Issue 2, p136 

    In this paper we describe the design and manufacture of an axial-torsion test specimen, and provide relationships needed when conducting stress-strain characterization experiments with the specimen. The specimen is a short hollow cylinder of rubber bonded between two steel mounting rings, in...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics